组合词时haz一般是哪个单词的缩写
发布网友
发布时间：2022-05-03 02:18
共1个回答
热心网友
时间：2022-06-19 08:16
HAZ缩写对应的词条意思
HAZ : Heat Affected Zone 热影响区
HAZ : Hannoversche Allgemeine Zeitung (German newspaper) 德国《图片报》(包括Zeitung Hannoversche)
HAZ : HAWK Assignment Zone 鹰作业区域
HAZ : Hazard/Hazardous 风险/危险
HAZ : Health Action Zone 健康行动区
HAZ : Mat Hazardous Materials 垫危险物品
HAZ : Hatzfeldthaven, Papua New Guinea Hatzfeldthaven、巴布亚-新几内亚
HAZ : Hayes Lemmerz International, Inc. 海耶斯Lemmerz国际有限公司
HAZ
HAZ 基本解释
热影响区；con hazard control 危险控制；hazard 危险；
HAZ 网络解释
1. 热影响区：由于不锈钢本身所具有的特性,与普碳钢相比不锈钢的焊接及切割有着其特殊性,更易在其焊接接头及 热影响区(HAZ)产生各种缺陷. 焊接时要特别注意不锈钢的物理性质. 例如奥氏体型不锈钢的热膨胀系数是低碳钢和高铬系不锈钢的1.5倍;
2. 危险：55、 GEAR SEL.LT 挡位指示灯 | 56、 HAZ 危险 | 57、 INST.LT 指示灯
3. 传送魔殿：HHMDSave------行会变量初始化行会名添加名单 | HAZ 传送魔殿 | GBW 天关变量
4. 危险,[警告灯]：HEATER 暖气 | HAZ 危险,[警告灯] | HORN 喇叭
5. haz：heat affected zones; 热影响区
6. haz：heat affect zone; 焊接haz
7. haz：heat affected zone; 高温影响区
HAZ 双语例句
1. Some alloys experience an additional solution heat treatment, while other alloys become overaged in the HAZ.
一些合金将使用辅助固溶热处理，而有些合金将在HAZ中过度时效。
2. And the effect of mechanical vibration on the impact absorbing energy of weld is greater than that of HAZ(heat-affected zone).
本文的试验中，将振动焊接技术应用于阀门筒体的环焊缝中，研究机械振动对焊接接头性能与组织的影响。1试验材料试验采用的材料为焊接阀门用A105钢，其化学成分
3. The result showed that weld and HAZ are narrow and no pore can be found in weld.
研究结果表明，焊缝和热影响区均较窄，焊缝中观察不到孔洞存在。
4. At the same time, the impact tenacity of the HAZ of the Ferrite Stainless Steel 4003 joints is higher than that of TCS material. The reason is that Ti content in 4003 is higher than that in TCS, which cause the microstructure more fine for the TiC and TiN dispersive distribution.
结果表明：由于德国4003材料含有较多的Ti元素，在热循环作用下，部分与C、N元素形成弥散分布的化合物，降低了晶粒组织长大，使得切割缝区和焊接接头热影响区的组织细小，接头热影响区冲击韧性值高于国产TCS材料的焊接接头。
5. This paper deals with the rules of hydrogen absorption of three types of HAZ structure formed in welding 30CrMnSiNi2A ultra-high strength steel, including the related diffusion coefficient and solubility of hydrogen in the overheated region of HAZ, the changes on the behavior of hydrogen diffusion after subzero treatment, and the sensitivity of the structues to hydrogen embrittlement.
本文用透射电镜，阴极电解法和定载延迟试验等方法，通过对30CrMnSiNi2A超高强钢模拟HAZ 组织结构对氢扩散行为和性能影响的考察，研究了三种HAZ组织的吸氢规律、三种HAZ 过热区组织中氢的扩散系数和溶解度，经冷处理后组织中氢扩散行为的变化，以及这些组织的氢裂敏感性。
6. Furthermore, the requirements to the location of notch of impact specimen of weld and HAZ, in some standards and technical specifications of steel pipe used for petroleum and natural gas transportation were discussed.
讨论了油气输送管道用钢管标准和技术条件对焊缝和热影响区冲击试样缺口位置的规定。
7. In the past, people investigate the transformation structure using heat simulation and metallographic or electron scanning. Today, with the development of computer technology, a new type of computer-aided system for testing and analyzing weld thermal cycle is presented in this paper.
在计算机技术高速发展的今天，为了更进一步丰富和发展焊接热影响区组织转变机理研究，本文采用计算机软件和硬件技术，研究开发了一种新型焊接热循环曲线测试及分析系统，并利用该系统适时采集了16MnDR和15MnMoVN两种低合金结构钢的焊接HAZ热循环数据。
8. The mechanical properties of HAZ are critical to the applications.
TCS不锈钢是一种低铬的经济型铁素体不锈钢，因为热循环的影响焊接HAZ性能成为制约其广泛应用的关键。
9. The results show that, in the location of weld junction and 1, 2, 5mm, E-class ship plate basically meets the needs of high heat input welding; In the HAZ after high heat input welding, ferrite steel has a smaller grain and a good toughness; and the impact ctility of the HAZ of FH32 and FH40 declines.
结果表明，E级船板钢在熔合线及1，2，5mm位置，均能够满足焊接的要求；焊接后的热影响区，铁素体晶粒较细，韧性良好。FH32和FH40钢的热影响区冲击韧性下降。
10. The microstructure of the coarse grained zone is consisted of coarse pearlite and little ferrite in the track steel side; the microstructure of the granular grained zone is consisted of granular pearlite and little granular sorbite. Hardness test showed that the hardness of HAZ of the track steel was higher than the hardness of HAZ of austentic manganese steel, but it was not uniform on whole HAZ, the hardness of the granular grained zone was higher than the hardness of coarse grained zone and the inadequacy re-crystal zone.
试验结果表明：闪光对焊接头ZGMn13高锰钢侧热影响区组织为单一的奥氏体组织，没有碳化物析出，其晶粒度明显小于母材；U71Mn钢轨侧过热区组织为晶粒较粗大的珠光体和少量铁素体，正火区为晶粒细小的珠光体组织，有些地方还有少量晶粒更加细小的索氏体组织。
11. Some pits were proced in the surface of the stainless steel owing to the rapping of the hammer with edge angle when carrying on cold assembly. The pitting corrosion occurred on the surface existing pits such as the welding spatter and arc scratch because of the changes of electrode potential. Moreover overheated HAZ were the location to the pitting corrosion. The pitting locat...
结果表明冷装配时带楞角铁锤敲击造成的表面凹坑处、焊接时飞溅与电弧擦伤处的电极电位发生了变化，促使了点蚀的发生；另外，HAZ的过热区也是点蚀最易发生的部位，并且点蚀发生部位也是应力腐蚀开裂的裂纹源。
12. The results indicated that excellent low temperature toughness and lower FATT could be obtained under different welding conditions in HAZ.
结果表明：在不同焊接条件下，此类钢焊接热影响区均具有较好的低温韧性和较低的韧脆转变温度。
13. But the hardness is uniform on the HAZ of austentic manganese steel side. The hardness of builp welding layer on the rail bottom is higher than the hardness of austentic manganese steel, but it is lower than the hardness of track steel. The tensile strength of flash butt welding joint is about 60% of the tensile strength of the track steel, and the impact toughness of the flash butt welding joint is above 60% of the impact toughness of the track steel.
高锰钢辙叉与钢轨闪光对焊接头的硬度分布：钢轨侧硬度较高，但热影响区硬度分布波动较大，正火区硬度较高，过热区和不完全重结晶区的硬度偏低；高锰钢侧硬度较低，分布较均匀；轨底堆焊层硬度介于高锰钢侧硬度值和钢轨侧硬度值之间。
14. The higher hardness and strength values in the HAZ and welding zone of Cr-Mo steel, compared to molybdenum steel, may be attributed to the higher amount of martensite phase in the alloy.
更高的硬度和强度值在焊接热影响区和区的Cr - Mo钢，钼钢相比，可能是由于较高数额的马氏体相合金中。
15. The effect of heat circulation ring welding to the microstructure evolution and vickers hardness change ofHAZ was analyzed.
分析了焊接热循环对焊接接头热影响区组织和维氏硬度分布的影响。
16. Indentation location was the main reason of test error because of great hardness gradient in HAZ. It was suggested that test location should be defined for vickers hardness test of...
因此 ，建议在制订标准时，应明确规定焊接接头热影响区维氏硬度试验的压痕位置，第一点压痕位置应在距熔合线约 0 。5mm以内的过热区内，每一压痕线上每一区域至少 3个压痕，间距为 0 。5～ 1mm
17. The hardness distribution of the weld is measured. The micro-structure of the weld is observed. The results show that when welding with no preheat, hard Martensite could be found in the HAZ of the cap weld. In multilayer weld, the hardness become lower and the micro-structure become Ferrite and Bainite.
测定了焊补接头的硬度分布，观察了相应部位的金相组织，得出：采用不预热焊补模拟裂纹缺陷，在接头近表面HAZ区容易出现淬硬的马氏体组织，硬度值高，由于多道多层焊道的相互热影响，硬度降低，组织一般为铁素体和贝氏体组织；而不预热焊补模拟缩松与缩孔等缺陷，硬度值不高。
18. The pitting corrosion occurred on the surface existing pits such as the welding spatter and arc scratch because of the changes of electrode potential.
结果表明冷装配时带楞角铁锤敲击造成的表面凹坑处、焊接时飞溅与电弧擦伤处的电极电位发生了变化，促使了点蚀的发生；另外，HAZ的过热区也是点蚀最易发生的部位，并且点蚀发生部位也是应力腐蚀开裂的裂纹源。
19. These results are confirmed by fracture toughness test on weld coarse grained HAZ of high strength steels.
通过对含硬化组织MA组元的高强钢焊接热影响区粗晶区的断裂性能试验，对上述分析结果进行了验证。
20. Weld heat affected zone microstructures of 22SiMn2TiB ultra-strength steel were thermally simulated by means of Gleeble-1500 machine. Polarization measurement of the quenched zone and tempered zone in 3.5%NaCl solution was concted respectively with potentionstat/galvanostat Solaron SL1280B.
采用Gleeble--1500热模拟试验机模拟了22SiMn2TiB超高强度钢焊接接头热影响区的组织，并利用Solaron SL1280B恒电位仪测定了热模拟HAZ各区在3.5\%NaCl水溶液中的极化行为，建立了热模拟组织与其在3.5%NaCl水溶液中腐蚀行为的关系。
HAZ 单语例句
1. It was unclear what prompted Haz to make his remarks in a speech to heads of Muslim boarding schools in Central Java.
